Changes between Version 20 and Version 21 of HetProcedures/RA/DIMM
- Timestamp:
- Nov 5, 2019 3:20:31 AM (5 years ago)
Legend:
- Unmodified
- Added
- Removed
- Modified
-
HetProcedures/RA/DIMM
v20 v21 10 10 * Turn on power to the Telescope on the base panel of scope 11 11 * Turn on power to the CCD which is on the far side of the enclosure as a small black box 12 * Turn on the computer monitor using the small fob next to the keyboard (might need to move mouse to wake it up) 13 * Select DIMM login and enter DIMM password 14 * Start the DIMM software on the desktop by clicking on the DIMM icon. This will start the CCD cooling 12 * Open the keyboard tray and turn on the computer monitor using the small fob next to the keyboard (might need to move mouse to wake it up) 13 * Select DIMM login and enter DIMM password (on post-it note under keyboard) 15 14 * Click the time and date on the computer in the lower right corner 16 * Using the computer hand-paddle hit Enter to choose noDaylight savings time15 * Using the telescope hand-paddle hit Enter to choose "no" Daylight savings time 17 16 * Using the hand paddle enter the computer time and then hit enter (be sure that you select AM or PM appropriately) 18 17 * Using the hand paddle enter the computer date 19 * Hit mode to get to the "Object" Menu and then hit Enter 20 * use the arrows at the bottom of the hand paddle to select "Star" and then hit Enter 21 * use the arrows at the bottom of the hand paddle to select "Named" and hit Enter 22 * use the arrows at the bottom of the hand paddle to find the star of interest (e.g., Deneb) and hit Enter 18 * Start the DIMM software on the computer by clicking on the DIMM icon on the Desktop. This will start the CCD cooling 19 * Using the hand paddle, press "mode" to get to the "Object" menu and then press Enter 20 * use the arrows at the bottom of the hand paddle to select "Star" and then press Enter 21 * use the arrows at the bottom of the hand paddle to select "Named" and press Enter 22 * use the arrows at the bottom of the hand paddle to find the star of interest (e.g., Deneb) and press Enter 23 23 * ''' Note always select stars that will stay north of the Zenith. '' 24 * on the hand paddle hitthe "GOTO" button24 * on the hand paddle press the "GOTO" button 25 25 * Turn on the reticle on the telrad finder 26 26 * select the number "1" on the hand paddle to set the speed and then hit another number to select the speed rate, e.g. 1=guide, 9=slew … … 28 28 * turn off the reticle 29 29 * change the flip mirror on the eye piece so that you can see the star images (there should be two). 30 * either turn on the reticle on the eye piece or shine your flashlight into the hole where the reticle screws in30 * shine your flashlight into the hole where the reticle screws in on the eyepiece to illuminate the rectangular boxes 31 31 * use the hand paddle to center the star images into the center of the boxes 32 32 * turn flip mirror to the CCD position and turn off the reticle 33 * on the telescope hand paddle, set the speed to "guide" 33 * on the telescope hand paddle, set the speed to "guide" (#1) 34 34 * sync the telescope with the current requested star by holding down the enter button for 5 seconds, then release. It should beep at you and say it sync'd 35 * on the DIMM set the speed radio button to "Guide" 36 * hit the "Start Seeing Measurements" button 35 * on the DIMM software, click the "Start Seeing Measurements" button 37 36 * '''Note:''' do not change the binning or exposure times or any other parameters as these may impact the seeing values that are determined. 38 * turn off the computer monitor using the small fob next to the keyboard, and close the door behind you 37 * also select the radio button for speed to "Guide", and check the "auto-center" check box 38 * once good seeing measurements are coming in, turn off the computer monitor using the small fob next to the keyboard, close the keyboard tray, and close the door behind you 39 39 40 40 === If the DIMM box gets too big due to winds or very bad seeing you can reset this by going under ''Settings'' and hit ''Apply'' without making any changes ===